Get Ready to Pass the 5V0-41.20 exam with VMware Latest Practice Exam
Get Prepared for Your 5V0-41.20 Exam With Actual VMware Study Guide!
NEW QUESTION 12
Scenario 2:
After completing the branch activation activities for all required branches, the network administrator attempts to test connectivity between the various branches and between the hubs and branches. The administrator notices a lack of connectivity despite being certain that configurations have been complete. The administrator also observed that several users are reporting intermittent connectivity to some of the applications they are accessing. Other users are reporting no access to these applications. Other users at some of the branches claim they cannot get to certain public resources. The administrator wants to ensure that all sites can talk to each other and all resources are accessible.
Exhibit.
A network administrator decides to deploy a local Checkpoint VNF appliance on the Edge in London to cut back on unnecessary traffic towards the NY Hub location. While attempting to deploy the VNF, the process keeps failing.
Where can the administrator check to see more detail?
- A. VCO > Monitor > Events
- B. VCO > Monitor > Logging
- C. VCO > Test & Troubleshoot > Remote Actions > Alerts
- D. VCO > Test & Troubleshoot > Remote Diagnostics > Events
Answer: A
NEW QUESTION 13
Scenario 3:
After resolving numerous connectivity issues throughout the various branch sites, connectivity between applications and users is finally present. The network administrator is informed that during certain tests, applications are not performing as they are expected to. Users report that call quality has not fully improved and that some of their calls either drop or have poor voice quality where the conversation is breaking up. Other users are noticing that file transfers are slower than expect. A group of users from a few sites have reported slowness in accessing internal and external applications.
Exhibit.
A network administrator is receiving complaints that a real-time voice application is not performing well, with choppy audio, and dead audio especially during peak traffic times.
What two actions can the administrator take to diagnose and fix the issue? (Choose two.)
- A. Check the status of the links using the QoE and Transport tabs for any degraded underlay issues or congestion issues.
- B. Configure a QoS policy to rate limit all traffic during peak times.
- C. Ensure that the realtime application is matching the correct application type using the diagnostics page.
- D. Configure a QoS policy to load balance the realtime traffic across all links.
Answer: A,B
NEW QUESTION 14
Scenario 2:
After completing the branch activation activities for all required branches, the network administrator attempts to test connectivity between the various branches and between the hubs and branches. The administrator notices a lack of connectivity despite being certain that configurations have been complete. The administrator also observed that several users are reporting intermittent connectivity to some of the applications they are accessing. Other users are reporting no access to these applications. Other users at some of the branches claim they cannot get to certain public resources. The administrator wants to ensure that all sites can talk to each other and all resources are accessible.
Exhibit.
A network administrator has received an email from the applications development team requesting connectivity to their AWS VPC.
The administrator has configured the tunnel via the VMware SD-WAN Gateway. The tunnel status icon has not turned green.
Where are two places the administrator must check? (Choose two.)
- A. Determine if the PSK is mismatched between the AWS side and the VeloCloud Gateway.
- B. Determine if the NVS has been enabled and assigned to a profile.
- C. Determine if the DH parameter on the Edge has been configured.
- D. Determine if the PSK is mismatched between the AWS side and the VeloCloud Edge.
Answer: A,D
NEW QUESTION 15
Scenario 2:
After completing the branch activation for all required branches, the network administrator attempts to test connectivity between the various branches and between hubs and branches. The administrator notices a lack of connectivity despite being certain that configurations have been complete. The administrator also observed that several users are reporting intermittent connectivity to some of the some applications they are accessing.
Other users are reporting no access to these applications. Other users at some of the branches claim they cannot get to certain public resources. The administrator wants to ensure that all sites can talk to each other and all resources are accessible.
Exhibit.
A technician has added Edges to an East Coast Profile. These Edges are not able to communicate via dynamic tunnels to Edges in the West_Coast profile. The technician has noticed that some Edges are able to establish dynamic tunnels.
What could be preventing Edges from being able to establish dynamic tunnels?
- A. The profiles are not configured to allow dynamic branch to branch VPNs.
- B. The profiles are configured to only allow dynamic branch to branch for Edges within the same profile.
- C. None of the existing profiles have Cloud VPN enabled thus preventing dynamic tunnels.
- D. Neither profile has been configured to utilize cloud gateways.
Answer: A
NEW QUESTION 16
Scenario 2:
After completing the branch activation activities for all required branches, the network administrator attempts to test connectivity between the various branches and between the hubs and branches. The administrator notices a lack of connectivity despite being certain that configurations have been complete. The administrator also observed that several users are reporting intermittent connectivity to some of the applications they are accessing. Other users are reporting no access to these applications. Other users at some of the branches claim they cannot get to certain public resources. The administrator wants to ensure that all sites can talk to each other and all resources are accessible.
Exhibit.
Several reports have come in from branch locations indicating customers cannot reach applications being served by the hub location. The hub location has a single LAN-side port from which it should be learning dynamic routes for the subnets serving the applications.
How should the technician verify if the ports on the Edge are up and working?
- A. Look in Test & Troubleshoot under the Remote Actions and run System Health.
- B. Look in Test & Troubleshoot under the Remote Diagnostics and run System Health.
- C. Look in Test & Troubleshoot under the Remote Diagnostics and run Interface status.
- D. Look under Administration and System Settings to verify if the interfaces are configured and enabled.
Answer: C
NEW QUESTION 17
Scenario 3:
After resolving numerous connectivity issues throughout the various branch sites, connectivity between applications and users is finally present. The network administrator is informed that during certain tests, applications are not performing as they are expected to. Users report that call quality has not fully improved and that some of their calls either drop or have poor voice quality where the conversation is breaking up. Other users are noticing that file transfers are slower than expect. A group of users from a few sites have reported slowness in accessing; internal and external applications.
Exhibit.
A network administrator is configuring several branches to prefer a single prefix, 10.20.11.0/24, from the Seattle hub over the New York hub for various application performance reasons.
What are two effective ways the administrator can accomplish this? (Choose two.)
- A. In the OFC 10.20.11.0/24, modify the preferred exit point to be Seattle and pin the route.
- B. In the hub preferred order in the profile, set the Seattle hub to be preferred over New York.
- C. Modify the AS Path in New York to be shorter for 10.20.11.0/24.
- D. Modify the AS Path in New York to be longer for 10.20.11.0/24.
Answer: A,B
NEW QUESTION 18
Scenario 3:
After resolving numerous connectivity Issues throughout the various branch sites, connectivity between applications and users is finally present. The network administrator is informed that during certain tests, applications are not performing as they are expected to. Users report that call quality has not fully improved and that some of their calls either drop or have poor voice quality where the conversation is breaking up. Other users are noticing that file transfers are slower than expect. A group of users from a few sites have reported slowness in accessing internal and external applications.
Exhibit.
Users at a remote office are complaining about poor performance with certain applications. The network administrator has already verified the configuration is correct.
Which two parameters should the administrator review to troubleshoot this issue? (Choose two.)
- A. Look under Monitor, check Business priority tab
- B. Check the underlay network (bandwidth, latency, jitter, packet loss)
- C. Change the bandwidth measurement under WAN Overlay Advanced Settings
- D. Check the flows to verify which Business Policy the traffic of interest is matching
Answer: A,B
NEW QUESTION 19
Scenario 1:
A network administrator is tasked! with enabling SO-WAN at three branch locations. A topology has been provided for reference. For each site, the administrator is having issues bringing edges online, as another administrator has gone ahead and created a configuration ahead of time. The organization has several branch sites- One is an Internet-only site and two are Hybrid locations with both internet and MPLS: The last location is MPLS only. There are hub data center locations in this environment as well. Please refer to the topology.
Exhibit.
An administrator is attempting to activate two Edge devices at the Chicago branch location. The local technician reports that the Edge devices are not coming online. The Edge devices have been plugged in, powered on, and connected to the correct circuits with an Enhanced HA setup.
What should the local technician check first when troubleshooting the issue?
- A. Review color of the LED.
- B. Review the Orchestrator for HA misconfiguration issues.
- C. Verify the link light sequence of the HA ports.
- D. Verify beep sequence of the Edge devices.
Answer: C
NEW QUESTION 20
Scenario 2:
After completing the branch activation activities for all required branches, the network administrator attempts to test connectivity between the various branches and between the hubs and branches. The administrator notices a lack of connectivity despite being certain that configurations have been complete. The administrator also observed that several users are reporting intermittent connectivity to some of the applications they are accessing. Other users are reporting no access to these applications. Other users at some of the branches claim they cannot get to certain public resources. The administrator wants to ensure that all sites can talk to each other and all resources are accessible.
Exhibit.
Where can the network administrator check to see what routes are present on the London-site Edge?
- A. Log into the VCO > Test & Troubleshoot > Remote Diagnostics > Run "Route Table Dump"
- B. Log into the VCO > Test & Troubleshoot > Remote Diagnostics > Run "List Paths"
- C. Log into the VCO > Configuration > Overlay Flow Control
- D. Log into the VCO > Monitoring > Overlay Flow Control
Answer: A
NEW QUESTION 21
Scenario 2:
After completing the branch activation activities for all required branches, the administrator attempts to test connectivity between the various branches and between the hubs and branches- The administrator notices a lack of connectivity despite being certain that configurations have been complete. The administrator also observed that several users are reporting intermittent connectivity to some of the applications they are accessing. Other users are reporting no access to these applications. Other users at some of the branches claim they cannot get to certain public resources. The administrator wants to ensure that all sites can talk to each other and all resources are accessible.
Exhibit.
The tunnel from the Dallas site to the Seattle hub is not coming up.
What are two things that should be checked to determine the issue? (Choose two.)
- A. Spoke Edge and Hub Edge have a mismatched certificate.
- B. Hub WAN Interface might be behind a firewall.
- C. Dynamic Branch to Branch is not enabled.
- D. Spoke Edge and Hub Edge are two different Edge models.
Answer: A,B
NEW QUESTION 22
Scenario 2:
After completing the branch activation for all required branches, the network administrator attempts to test connectivity between the various branches and between hubs and branches. The administrator notices a lack of connectivity despite being certain that configurations have been complete. The administrator also observed that several users are reporting intermittent connectivity to some of the some applications they are accessing. Other users are reporting no access to these applications. Other users at some of the branches claim they cannot get to certain public resources. The administrator wants to ensure that all sites can talk to each other and all resources are accessible.
Exhibit.
A technician has added Edges to an East Coast Profile. These Edges are not able to communicate via dynamic tunnels to Edges in the West_Coast profile. The technician has noticed that some Edges are able to establish dynamic tunnels.
What could be preventing Edges from being able to establish dynamic tunnels?
- A. The profiles are not configured to allow dynamic branch to branch VPNs.
- B. The profiles are configured to only allow dynamic branch to branch for Edges within the same profile.
- C. None of the existing profiles have Cloud VPN enabled thus preventing dynamic tunnels.
- D. Neither profile has been configured to utilize cloud gateways.
Answer: B
NEW QUESTION 23
Scenario 1:
A network administrator is tasked with enabling SD-WAN at three branch locations. A topology has been provided for reference. For each site, the administrator is having issues bringing edges online, as another administrator has gone ahead and created a configuration ahead of time. The organization has several branch sites. One is an Internet-only site and two are Hybrid locations with both internet and MPLS. The last location is MPLS only. There are hub data center locations in this environment as well. Please refer to the topology.
Exhibit.
The network administrator determines the issue preventing the Dallas Branch from coming online.
Refer to the Exhibit(s).
What must the administrator do for the Edge to communicate with the Orchestrator and other branches?
- A. Reverse the WAN Overlay configurations
- B. Delete the User Defined WAN Overlays as the Orchestrator will discover these automatically on MPLS and Internet
- C. Update the Orchestrator to the latest version as it enables "Auto WAN Swapping"
- D. Create a User-defined WAN Overlay to bond both interfaces
Answer: B
NEW QUESTION 24
Scenario 2:
After completing the branch activation activities for all required branches, the network administrator attempts to test connectivity between the various branches and between the hubs and branches. The administrator notices a lack of connectivity despite being certain that configurations have been complete. The administrator also observed that several users are reporting intermittent connectivity to some of the applications they are accessing. Other users are reporting no access to these applications. Other users at some of the branches claim they cannot get to certain public resources. The administrator wants to ensure that all sites can talk to each other and all resources are accessible.
Exhibit.
A network administrator is trying to create multiple overlays on a single physical interface on an Edge. The administrator is able to bring up only a single overlay so far, but is having trouble with bringing up additional overlays.
What could be the possible reason?
- A. The licensing does not support multiple overlays on a single physical interface.
- B. Multiple overlays cannot be created on a single physical interface. Multiple physical interfaces are needed.
- C. On the WAN overlay configuration, verify the IP address, next-hop, and the VLAN ID configuration.
- D. The administrator does not have the right permission to create multiple overlays. The administrator needs to have an Operator-level privilege for this task.
Answer: A
NEW QUESTION 25
Scenario 3:
After resolving numerous connectivity Issues throughout the various branch sites, connectivity between applications and users is finally present. The network administrator is informed that during certain tests, applications are not performing as they are expected to. Users report that call quality has not fully improved and that some of their calls either drop or have poor voice quality where the conversation is breaking up. Other users are noticing that file transfers are slower than expect. A group of users from a few sites have reported slowness in accessing internal and external applications.
Exhibit.
The network administrator has been made aware that Chicago is receiving traffic from non-SD-WAN sites, bottlenecking Chicago's interfaces. The network administrator's VMware SE has mentioned using the uplink feature to help resolve this.
What are two ways the uplink feature should be used in this scenario? (Choose two.)
- A. Stop mutual redistribution of routes from underlay and overlay.
- B. Direct all traffic to that neighbor designated as an uplink,
- C. Prevent the site in question from becoming a transit site.
- D. Set the uplink community to forward traffic to a group of neighbors.
Answer: B,C
NEW QUESTION 26
Scenario 2:
After completing the branch activation activities for all required branches, the network administrator attempts to test connectivity between the various branches and between the hubs and branches. The administrator notices a lack of connectivity despite being certain that configurations have been complete. The administrator also observed that several users are reporting intermittent connectivity to some of the applications they are accessing. Other users are reporting no access to these applications. Other users at some of the branches claim they cannot get to certain public resources. The administrator wants to ensure that all sites can talk to each other and all resources are accessible.
Exhibit.
One branch location is not able to communicate with another branch location via dynamic branch-to-branch tunnels. While troubleshooting at the Edge configuration level, the network administrator notices Cloud VPN is not enabled and is grayed out, preventing them from enabling that feature.
- A. Within the Configuration section under Customer VPN enablement.
- B. Within the Configuration section under Profiles. Within the Monitor section under Network Services.
- C. Within the Test & Troubleshooting section under Remote Diagnostics.
- D. Where is the next location to check for and enable the necessary feature?
Answer: A
NEW QUESTION 27
Scenario 2:
After completing the branch activation activities for all required branches, the network administrator attempts to test connectivity between the various branches and between the hubs and branches. The administrator notices a lack of connectivity despite being certain that configurations have been complete. The administrator also observed that several users are reporting intermittent connectivity to some of the applications they are accessing. Other users are reporting no access to these applications. Other users at some of the branches claim they cannot get to certain public resources. The administrator wants to ensure that all sites can talk to each other and all resources are accessible.
Exhibit.
One branch location is not able to communicate with another branch location via dynamic branch-to-branch tunnels. While troubleshooting at the Edge configuration level, the network administrator notices Cloud VPN is not enabled and is grayed out, preventing them from enabling that feature.
- A. Within the Configuration section under Customer VPN enablement.
- B. Within the Configuration section under Profiles. Within the Monitor section under Network Services.
- C. Within the Test & Troubleshooting section under Remote Diagnostics.
- D. Where is the next location to check for and enable the necessary feature?
Answer: A
NEW QUESTION 28
......
Pass Your Next 5V0-41.20 Certification Exam Easily & Hassle Free: https://pass4sure.dumps4pdf.com/5V0-41.20-valid-braindumps.html