NACE-CIP1-001 Practice Test Questions Updated 100 Questions
NACE NACE-CIP1-001 Dumps - Secret To Pass in First Attempt
NACE-CIP1-001 Exam covers a wide range of topics related to coatings inspection, including surface preparation, coating application, inspection methods, and safety. Coating Inspector Level 1 certification program is based on a set of industry-recognized standards and guidelines, including those developed by NACE International, SSPC (the Society for Protective Coatings), and other organizations. Individuals who pass the exam are recognized as having a basic level of knowledge and understanding of coatings inspection, and are able to perform inspections in accordance with the applicable standards and guidelines.
NEW QUESTION # 28
Which of these tests uses a syringe?
- A. Sleeve test
- B. Potassium ferricyanide
- C. Soluble salts meter
- D. Bresle patch
Answer: D
NEW QUESTION # 29
ASTM Standards are applicable:
- A. When specified
- B. In Asia
- C. In the USA
- D. In North America
Answer: A
NEW QUESTION # 30
You are the NACE Inspector on a 5000 sq. ft. job where SSPC PA 2 has been specified.
Assuming all areas are in compliance, how many gauge readings and spot measurements are required?
- A. 75 Gauge Readings resulting in 25 Spot Measurements
- B. 105 Gauge Readings resulting in 35 Spot Measurements
- C. 225 Gauge Readings resulting in 75 Spot Measurements
- D. 45 Gauge readings resulting in 15 Spot Measurements
Answer: C
NEW QUESTION # 31
Which is a component that supplies most of the features and functions of the material?
- A. solvent
- B. binder
- C. pigment
- D. additive
Answer: B
NEW QUESTION # 32
Fine cracks in the surface of a coating that rarely reach the substrate are called
- A. checking.
- B. alligatoring.
- C. blistering.
- D. cracking.
Answer: A
NEW QUESTION # 33
You are asked to be the only coating inspector on a small bridge recoating job where existing coating contains lead. The owners' representative has supplied you with the local code governing the removal and disposal of lead based coatings, however upon reading the document you having great deal of difficulty understanding the technical language.
As a NACE CIP Level 1 Inspector your preferred course of action is to:
- A. Advise the owners' representative of your lack of knowledge in this area
- B. Minimize your lack of understanding and go ahead with the inspection task to the best of your ability
- C. Hire a third patty to assist you in understanding the document
- D. Carefully review the document and do the best you can
Answer: D
NEW QUESTION # 34
The least effective method of surface cleaning is most likely
- A. hand tool cleaning.
- B. water blasting.
- C. dry grit blasting.
- D. power tool cleaning.
Answer: A
NEW QUESTION # 35
You are the NACE Inspector on a job where ISO ST 3 has been specified. The Contractor normally works to SSPC standards and been referencing SSPC SP 3.
Could this have any impact on the final surface preparation appearance?
- A. Yes, because the 'two standards are not equivalent
- B. It depends on which hand tool the Contractor selects
- C. No, because there is no real difference in the standards
- D. It depends on which power tool the Contractor selects
Answer: C
NEW QUESTION # 36
When applying Thermal Spray Coatings the specification is most likely to refence:
- A. NACE SP 0188
- B. SSPC-CS 23.00/AWS C2.23/NACE No. 12
- C. NACE SP 0178
- D. SSPC PA 2
Answer: B
NEW QUESTION # 37
ISO SA 3 is directly equivalent to:
- A. NACE No. 3/SSPC SP 6
- B. None of the above
- C. NACE No. 2/SSPC SP 10
- D. NACE No. 1/SSPC SP 5
Answer: B
NEW QUESTION # 38
Surface profile describes:
- A. The initial condition of the surface prior to abrasive blasting
- B. The level of surface cleanliness required after abrasive blasting
- C. The general condition of the surface required after abrasive blasting
- D. The level of surface roughness required after abrasive blasting
Answer: D
NEW QUESTION # 39
On a blast-cleaned surface, Ian ultraviolet light is generally used to detect
- A. grease and oil
- B. sulfates
- C. soluble chemical salts
- D. inhibitor residues
Answer: A
NEW QUESTION # 40
The form of corrosion that has the largest potential for unexpected catastrophic failure is:
- A. Galvanic Corrosion
- B. Localized Corrosion
- C. Atmospheric Corrosion
- D. General Corrosion
Answer: A
NEW QUESTION # 41
Common errors that can produce inaccurate readings when using Wet Film Thickness (WFT) gauges include:
Select All That Apply
- A. Dragging a gauge through wet coating
- B. Using a damaged gauge
- C. Placing the gauge along the longitudinal axis
Answer: A,B
NEW QUESTION # 42
The main responsibilities of the inspector are to
- A. demonstrate to the contractor how to apply the coating.
- B. observe and report the quality of the work performed.
- C. observe and direct the work of the contractors.
- D. direct and perform the work stated in the specification.
Answer: B
NEW QUESTION # 43
To achieve consistently accurate results with ALL alt test equipment
- A. avoid placing the sample discs on a surface.
- B. wear gloves when sampling.
- C. calibrate the instrument in the field.
- D. wash your hands before sampling.
Answer: D
NEW QUESTION # 44
A magnetic pull-off type gauge is a good choice when:
- A. Performing an adhesion test
- B. When working on non-ferrous metals
- C. When an intrinsically safe tool is required
- D. Accuracy is not required
Answer: C
NEW QUESTION # 45
Which one of the following documents is the best source for coating technical data:
- A. Safety Data Sheet;
- B. Application Guidelines
- C. Specification
- D. Technical Data Sheet
Answer: D
NEW QUESTION # 46
Prior to using Inspection Tools the inspector must:
- A. Be trained on how to use the instrument
- B. Ensure the instrument is within calibration parameters
- C. Read the manufactures' instructions
- D. a), b) & c)
Answer: D
NEW QUESTION # 47
......
NACE NACE-CIP1-001 Exam Dumps [2024] Practice Valid Exam Dumps Question: https://pass4sure.dumps4pdf.com/NACE-CIP1-001-valid-braindumps.html